Time-of-Flight Sensor - Goermicro

The new SOT26-001, is a highly integrated, compact single point direct Time of Flight (dToF) sensor module which integrates a VCSEL emitter, a single photon avalanche diode (SPAD) sensor, microlens, Time Digital Converter (TDC) and MCU. Small size: 4.4×2.4×1.0 mm

This sensor uses dTOF technology, built in sunlight suppression and anti cover dirt algorithm. The measurement accuracy is not affected by reflectivity of the target object in different environments, and can achieve accurate ranging of up to 4m.

Applications:
- Distance measurement
- Proximity detection
- Collisions avoidance
- 1D gesture recognition
- Object detection
 

Experience the clarity and stunning visuals with this 2.4" IPS Display - Startek

Whether you're showcasing your product or creating an immersive user interface, the IPS display delivers excellence in every pixel. Elevate your viewing experience to a new level with vibrant colors, wide viewing angles, and crystal-clear resolution with this 2.4" IPS display.

- 2.4 inch, full viewing angle, sunlight readable
- Display colors: 65K/262K
- Resolution (pixels): 240(RGB)*320
- Pixel pitch: 0.153 (H) x 0.153 (V)
- Viewing direction: ALL (160O)
- Controller IC: ST7789V
- Display mode: Transmissive/ Normally Black
- Luminance: 550cd/m2
- 8080 8/9/16/18bit MCU interface, 3/4 SPI+ 16/18bit RGB interface,
  3/4 line serial interface
 

AIC1508, 8-Bit HV Parallel Driver IC - Apex Microtechnology

The AIC1508 is a rigid, low-cost general purpose high voltage driver IC with 8 high voltage push-pull outputs. The device has been designed for harsh industrial applications and allows a wide application area.

The outputs can drive capacitive and resistive loads such as piezoelectric transducers, electroluminescent devices and micro-mechanical actuators. The maximum operating voltage is 300V, and each output has a source-sink capability of up to 40mA.

Target applications include driving capacitive actuators, piezo transducer excitation, and electro-luminescent displays.
 

AIC1532, 32-Channel High Voltage Driver - Apex Microtechnology

The AIC1532 is a 32-bit serial to parallel converter IC with 32 high voltage push-pull outputs and TTL compatible input signals.

The outputs are designed to drive capacitive and resistive loads.
An internal protection function monitors the logic supply voltage (VDD) and disables all output transistors of the high voltage push-pull outputs if an undervoltage condition is detected. Output supply voltage ranges from 30-230V.

Target applications include driving capacitive actuators, piezo transducer excitation, and electro-luminescent displays.
 

LTE-A Cat 6, M.2 Module - Quectel

Quectel’s latest product features an LTE Advanced Category 6 M.2 module for the EMEA, APAC and Brazil markets.

The EM060K-EA is powered by a Snapdragon® X12 LTE Modem from Qualcomm Technologies Inc which adopts 3GPP Release 12 technology. It supports 4G, 3G and GNSS with a theoretical peak date rate of 300 Mbps downlink and 50 Mbps uplink on the LTE network.

A rich set of Internet protocols, industry-standard interfaces and abundant functionalities (USB drivers for Windows, Linux, Android/ optional built-in eSIM),extend the applicability of the module to a wide range of applications such as industrial routers, home gateways, set-top boxes, industrial laptops, consumer laptops, industrial PDAs, rugged tablet PCs, and digital signage, etc
 

600W on-board charger suitable for a full range of input voltages - FSP Group

This 600W charger FSP600-1UAC01 is suitable for a full range of input voltages, with an output voltage of 50.4V-58.8V and an output current of 10A.

The charger has a streamlined appearance and a compact size of only 202x132x69mm/2.2kg. It is designed with a small, compact, high-efficiency concept and has an IP65 rating to provide protection against dust, dirt, and water.

By using FAN cooling within a fully enclosed mechanical enclosure, the surface temperature remains effectively lower. Custom cables, connectors, and charging profiles are possible to meet your specific needs.

Optional integration of the CANBUS protocol further enhances adaptability. This on-board charger is applicable in various settings, including e-bikes, e-scooters, AGVs, and AMRs.
 

High Temp Core camera, with wider detection range - Seek Thermal

The camera core, C314HPX, allows for imaging over a broader range, utilization under more elevated operating conditions, and improved thermal accuracy. 

It's fully calibrated and comes with a protective Germanium window which makes it easy to design into products and housings.

The camera’s compact design 20 x 20 x 15mm (L x W x H), mixed-gain pixel technology, and Seek’s proprietary SV1 Image optimization filters make for a powerful and highly sensitive thermal camera.

Specifications
320 x 240 Sensor HFOV: 35°
-20°C to 650°C (-4°F to 1202°F) Detection range
27Hz Frame Rate